Miele Oven Not Heating

Common Symptoms

• Oven displays F1 or F2 fault code and will not heat
• Oven turns on but never reaches the set temperature
• Bake mode works but broil does not (or vice versa)
• Oven heats briefly then shuts off
• Pyrolytic self-clean cycle will not start

Most Likely Causes

1. 1

   F1 / F2 Temperature Sensor (NTC Probe) Fault

   The NTC (Negative Temperature Coefficient) probe measures oven cavity temperature. F1 typically indicates a short-circuit in the probe circuit; F2 indicates an open circuit. The probe is a ceramic resistor: at room temperature (25°C / 77°F) it should read approximately 1080 Ω. A reading far outside this range (open, shorted, or unstable) triggers F1/F2 and prevents any heating element from activating.

2. 2

   Failed Bake or Broil Heating Element

   Electric Miele ovens use separate elements for bake (lower, hidden beneath the oven floor) and broil (upper). A burned-out element will show no continuity on a multimeter. Spec resistance: bake element approximately 25 Ω; broil element approximately 18 Ω. Visible burn spots, cracks, or blistering on the element surface confirm failure without testing.

3. 3

   Blown Thermal Fuse / Thermal Cutout

   Miele electric ovens include a thermal cutout (typically rated at 280–320°C) that permanently opens if the oven overheats. This is a safety device — once it blows, the oven will not heat at all. It is located near the control board or on the oven cavity housing and tests as open-circuit (no continuity) when failed. Identifying WHY it blew (blocked ventilation, cooling fan failure) is as important as replacing it.

4. 4

   Control Board Fault

   The control board governs heating element relay switching and sensor input processing. Visible burn marks, corroded relay contacts, or capacitor bulging on the board indicate board failure. F1/F2 codes that persist after the probe tests good and all other components check out usually indicate a board issue. On H 7000 series, the display board and control board are separate — both can fail independently.

5. 5

   Pyrolytic Self-Clean Lockout

   During or immediately after a pyrolytic self-clean cycle, the oven door locks and the control system restricts normal operation until the cavity cools below approximately 300°C. If the temperature sensor has failed, the oven may believe it is still in a pyrolytic cycle and refuse to heat. Resolve any sensor fault before attempting another self-clean.

Quick DIY Checks

1. 1SAFETY: Disconnect the oven from the mains supply at the circuit breaker (double-pole breaker, 30–50A for electric models). For gas Miele ovens, also close the gas shut-off valve. Verify no voltage is present with a non-contact voltage tester before touching any internal components.
2. 2CAPACITOR DISCHARGE (electric models): Before touching any control board components, discharge the board capacitors. Use a 10 kΩ 10 W resistor with insulated leads — place one lead on each capacitor terminal for 30 seconds. Do not bypass this step. Oven board capacitors can hold several hundred volts even minutes after power is disconnected.
3. 3Test the NTC temperature probe: Pull the oven away from the wall enough to access the rear panel. Locate the NTC probe (usually a small ceramic cylinder secured with one screw inside the oven cavity, with two leads exiting through the back). Disconnect the connector and measure resistance with a multimeter. At room temperature (25°C / 77°F) expect approximately 1080 Ω. Below 500 Ω or above 2000 Ω (or open/shorted) = replace the probe.

Repair vs Replace

Recommended Tools & Parts

• Miele NTC Temperature Probe / Sensor

  OEM NTC sensor for H 6000 and H 7000 series ovens. Verify your model number on the label inside the door frame before ordering — sensor resistance spec varies by model year.

  $30–$60

  Buy on Amazon →

• Miele Bake Heating Element (Lower)

  Concealed bake element for electric Miele ovens. Model-specific — a wrong element will have incorrect wattage and may trip the thermal fuse. Always order by model number.

  $55–$110

  Buy on Amazon →

• Miele Broil Element (Upper)

  Upper broil element for electric Miele wall ovens. Check wattage rating matches original (typically 2400–3000 W on H 6000/7000 series).

  $50–$100

  Buy on Amazon →

• Thermal Cutout / Thermal Fuse

  Safety thermal cutout for Miele ovens. Match the trip temperature rating (usually 280–320°C) and connector type to the original. Never substitute a higher-rated fuse.

  $12–$30

  Buy on Amazon →

• Miele Door Gasket / Oven Seal

  Replacement door seal for H 6000 and H 7000 series. A torn seal reduces efficiency and can trigger thermal safety shutoffs.

  $40–$80

  Buy on Amazon →

• Digital Multimeter

  Required for NTC probe resistance test, element continuity check, and thermal fuse test. Any multimeter with resistance and continuity modes is sufficient.

  $15–$30

  Buy on Amazon →

• 10kΩ 10W Resistor (Capacitor Discharge)

  Used to safely discharge control board capacitors before any board-level work. Essential safety tool — do not substitute a lower wattage resistor.

  $3–$8

  Buy on Amazon →

Links are Amazon affiliate links (tag: fixitfastai-20). Prices are estimates.

Related Repair Guides

This section combines editorial `relatedSlugs` from the article source with metadata-based matches so each guide links deeper into the repair library.